KEYENCE LS-7601 PDF

Precautions for CE Markings Keyence confirms that the LS Series . LS- Photoelectric Sensor or Proximity Sensor Timing input signals are sent. Find great deals for 1 PC KEYENCE Ls CCD Laser Micrometer. Shop with confidence on eBay!. LS High-performance controller. Visible measurement pointController with Target Viewer. High-durability CCD . The LS Series measures the outer diameter of a fiber continuously and .. E-mail: [email protected]

Author: Fausar Kigalar
Country: Zambia
Language: English (Spanish)
Genre: Love
Published (Last): 15 April 2008
Pages: 370
PDF File Size: 9.80 Mb
ePub File Size: 20.31 Mb
ISBN: 682-9-23993-956-1
Downloads: 1932
Price: Free* [*Free Regsitration Required]
Uploader: Arashirr

Circumscribed circle External dia. Chapter 1 Getting Started Use the 5-mm-deep M4 bottom mounting holes of the transmitter and receiver as shown in the illustration. It is possible to make calibration settings for each area independently.

The LS Series completes statistical sampling and starts statistical processing. Chapter 6 Environment Settings Key Lock Take the following steps to specify the key lock range when the key lock function is set.

keyencw Chapter 5 Function Settings Calibration Type Selection The following section provides information on how to set the calibration type for each area. The image of the target does not appear.

Chapter 10 Troubleshooting Problem The measured value is not displayed.

Chapter 1 Getting Started This section provides information on the configuration of the LS Series, precautions, and necessary preparations required before operating the LS Series.

When the LS Series receives command L measured value outputthe internal timing is triggered and the determined measured value will be returned. Normal Measurement of maximum value within specified period.

  ESTENOSE HIPERTROFICA DO PILORO PDF

KEYENCE LS : Manual

The results of difference checks will be output externally, provided that DIFF function output settings are made properly in advance. The following section provides information on how to mount the measuring head with or without the TR base employed, along with mounting conditions required. Chapter 5 Function Settings Calibration Settings The measured value of an target may have a delicate error due to the surface condition and angle of the target.

Page 13 Appendix List of Optional Accessories Page Chapter 5 Function Settings Dual Head Function The dual head function uses two measuring heads to measure the width of sheet material or the outer diameter of thick targets that are too large to be measured with a single head. For warranty information about this product, please click here Would you like to tell us about a keyencr price? Appendix Index 1 One-point calibration The following section provides information on respective command formats.

Appendix-3 Environment Setting Record Sheet Page Chapter 10 Troubleshooting This section provides information on troubleshooting and the contents of error messages. Withoutabox Submit to Film Festivals. Chapter 4 Operation Control Key Lock Function This function locks the control panel and remote control console, thus disabling key input.

These commands keyenec the following operations. Chapter 1 Getting Started 3 Connect the cable between the controller and measuring head.

1 PC KEYENCE Ls-7601 CCD Laser Micrometer

Page 46 Chapter 3 Easy Setting Guide Measurement of Outer Diameter and Eccentricity In the following example, the outer diameter and eccentricity of the roller is measured while the roller moves. All digits turn ON Appendix List of Optional Accessories Tips Communication settings for the RSC interface vary with the peripheral device to be connected or the type of output desired. Calibration setting error Remedy Check the wiring of the connection cable.

  MAIRONIS PAVASARIO BALSAI PDF

The average values are used to determine the measured values. Otherwise, the settings may be partially or completely lost. Appendix Environment Setting Record Sheet Use the following tables to record your environment setting details. The results of output are displayed as OUT2. The LCD monitor changes from the program setup screen to the environment setup screen.

Refer to the following information for the outline of each mode.

When repeating the one-point calibration, the previous settings will appear on the screen, which will be different from those in the above setting example.

Chapter 5 Function Settings Offset An offset value is a desired value that can be added to or subtracted from kyeence values. Chapter 3 Easy Setting Guide 3 Provides information on targets and settings for typical applications respectively.

Chapter 3 Keynce Setting Guide Measurement of Inner Diameter and Clearance In the following example, the inner diameter of the workpiece is measured while the workpiece moves.

TR Base Used to mount the transmitter and receiver. Varies by a few percent according to the unit. A through D is used as criteria.

Chapter 10 Troubleshooting This section provides information on troubleshooting and the contents of error messages.